Skip to main content

Filter By:

  • Show More Brands

  • Show Fewer Brands
  • Show More Sizes
  • Show Fewer Sizes

Tools

Park Tool Bottom Bracket Tool (Octalink / Isis)
$17.95
Park's BBT-18 is a heavy duty, investment cast tool for installing and removing all Shimano, ISIS Drive, and ISIS Overdrive 8-notch bottom bracket cups.
Park Tool Bottom Bracket Tool - Shimano Dura-Ace/XTR
$22.95
The BBT-29 is a double-ended bottom bracket wrench designed to fit 16-notch bearing cups with an outside diameter of 39mm (e.g. Shimano Dura-Ace 9000 series and XTR 980 series) as well as 16-notch bearing cups with an outside diameter of 48.5mm (e.g. FSA MegaEvo).
Park Tool CM-5.3 Cyclone Chain Scrubber
$26.95
Cleans bicycle chain quickly, easily, and effectively — without the hassle and mess of removing the chain from the bike. The Cyclone uses a large solvent reservoir, hundreds of rotating bristles, and a two-step cleaning process to get chains really clean, improve shifting performance, and extend the life of the chain and other expensive drivetrain parts. - Works with all multi-speed bikes (5, 6, 7, 8, 9, 10, 11, and 12-speed) as well as some single-speed models and e-bikes - Strong magnet at the bottom of the fluid reservoir holds metallic particles scrubbed from the chain - Special wicking sponge draws solvent from the chain as it exits, minimizing drips and mess - Sturdy handle makes the Cyclone easy to use and control - Holds 2 fluid ounces (59ml) of solvent
Park Tool Campagnolo Crank and Bearing Tool Set
$96.95
A complete tool set to work on both Campagnolo and Fulcrum Ultra-Torque and Power Torque crank and bottom bracket systems (each sold separately). The CBP-8 includes a beefed-up bearing and crank puller and all the fittings necessary to remove and install both systems. - Bearing Puller That Fits Both Power Torque And Ultra-Torque - Crank Puller For Power Torque - Bearing Setter For Both Power Torque And Ultra-Torque - Removal Adaptor For Power Torque Crank Bearings - Removal Protection Pads For Use With Carbon Cranks - Removal Protection Adaptor For Use With Aluminum Crank Arms - Crank Removal Extension Plug For Power Torque
Park Tool Carbon Saw Blade
$8.95
• 12” Tungsten steel hacksaw blade specially designed to smoothly cut carbon composite handlebars, forks, seat masts, seat posts, etc. • Fits Park Tool SAW-1 Hacksaw and most 12” hacksaws • The CSB-1 is designed for use with the SG-8 Saw Guide. NOTE: Similar to a grinding stone, do not use this blade on aluminum
Park Tool Corkscrew Bottle Opener
$45.95
In the tradition of our premium quality fold up tools, the BO-4 is a combination corkscrew and bottle opener complete with a knife/foil cutter. This multi-tool folds for storage and features all stainless steel mechanisms housed in a forged aluminum case. This is a top quality beverage tool perfect for the workbench, toolbox or wine bar.
Park Tool Crank Puller (Square Taper)
$15.95
A favorite of shop mechanics for over 30 year's, Park's CCP-22 Crank Puller removes crankarms that feature square tapers, and those that fit on Power Drive and Power Spline bottom bracket interfaces. The long, comfortable, built-in handle and fine thread provide the leverage needed to remove even the tightest crankarms. And, there's a rotating tip to ensure smooth operation and long life.
Park Tool Crank Wrench
$11.95
Now you can easily tackle any crank bolt with Park's Crank Wrench. It features a dual-sided head with a 14mm socket and 8mm Allen wrench on a long, vinyl-coated handle so you're sure to have the leverage necessary for the job.
Park Tool Crown Race Setting System Extension
$33.95
The CRS-15EXT includes a tube and fitting to extend any CRS-15 to work on fork steering tubes up to 425mm.
Park Tool Cutting Facer
$145.02
Park Tool has long provided some of the best cutting and machining tools in the bicycle industry. Their 690 Cutting Facers reflect their commitment to maintaining this high level of quality. Please read below for use and compatibility information specific to each size cutter: - 45mm (690): The 690 cutting facer is used on the HTR-1, HTR-1B, BFS-1, and BTS-1 cutting and facing tools. The facer has an outside diameter of approximately 45mm. - 57mm (690XL): The 690-XL is a larger version of the 690 facer for the HTR-1 Head Tube Reamer and Facer. It has a nominal outside diameter of 57mm. It may be used in conjunction with the 788 reamer. It is also used with the 767 Pilot or the 768 Pilot to face only the large diameter headtubes used with, "low profile," ZS-type headsets. - 65mm (690-XXL): The 690-XXL faces large headtubes. It has a nominal outside diameter of 65mm. Use the 690-XXL facer with the 750.2 Centering Cone Adaptor and 789 Reamer or 790 Pilot when facing head tubes with internal diameters of 55.95–55.90mm.
Park Tool DHD Precision Hex Drivers
$31.95
Professional quality component hex driver precisely machined to exact standards to ensure a perfect fit on compatible component fasteners. Featuring an ergonomic, CNC machined, perfectly balanced 6061 aluminum handle hard anodized to take the rigors of everyday use.
Park Tool Derailleur Clutch Wrench
$6.95
Park Tool's Derailleur Clutch Wrench is a small, thin wrench with 5.5mm and 3mm openings designed to fit the rear derailleur clutch tension adjuster on Shimano XT, SLX, Deore, Saint and Zee rear Shadow Plus (+) derailleurs and all previous Shadow Plus models.
Park Tool Derailleur Screwdriver
$32.95
Precision component screwdriver machined to exact standards to ensure a perfect fit on compatible component fasteners. Featuring an ergonomic, CNC machined and hard anodized 6061 aluminum handle.
Park Tool Double-Ended Cone Wrench
$5.95
Park's Double-Ended Cone Wrenches are designed for home mechanics. They're made of thin tool steel to fit the low-clearance adjusting nuts and cone flats on a variety of bearing assemblies. Each wrench is chrome plated for long life and available in popular combinations from 11 to 18mm. Most applications require a pair of cone wrenches. Call or stop by. We can recommend the correct sizes for your needs.
Park Tool Double-ended Spoke Wrench: Campagnolo
$11.95
Park Tool's SW-11 is a forged, double-ended spoke wrench designed to fit select Campagnolo wheels. Precision machined, plated and vinyl dipped for comfort and long life. It fits Campagnolo 5.5mm and 6.0mm hex spoke nipples.
Park Tool Dummy Hub
$19.95
Also called a sleeping hub, the Dummy Hub slides into rear dropouts and replaces the rear wheel for chain cleaning and transport. The DH-1 works with all derailleur and 1/8" chain. The unique design allows the bike to be shifted and works with open dropout and thru-axle frames up to 12mm.
Park Tool FR-2 Freewheel Remover
$11.95
The Park FR-2 Freewheel Remover fits SunTour two-notch freewheels. It's built thin so that removing axle parts is unnecessary. And, it's constructed of durable heat-treated steel. (Not recommended for use with SunTour 4- and 6-notch freewheels.)
Park Tool FR-4 Freewheel Remover
$7.95
The Park FR-4 Freewheel Remover fits Atom, Regina, splined Zeus and some Schwinn-approved freewheels. It's built thin so that removing axle parts is unnecessary. And, it's constructed of durable heat-treated steel.
Park Tool FR-7 Freewheel Remover
$7.95
The Park FR-7 Freewheel Remover fits Falcon freewheels. It's built thin so that removing axle parts is unnecessary. And, it's constructed of durable heat-treated steel.
Park Tool Facing Pilot
$18.46
Park Tool has long provided some of the best cutting and machining tools in the bicycle industry. Their centering pilots demonstrate their commitment to maintaining this high level of quality. Please read below for use and compatibility information specific to each size pilot: - 49.8mm (for 1.5-inch standard): The 767 is used with the HTR-1 (HTR-1B) and 690XL facer to perform facing only. It fits head tubes with an inside diameter of 49.8mm (1.5" standard). - 43.8mm (for ZS44 and EC44): The 768 Pilot is used with the HTR-1 (HTR-1B), the 750 Centering Cone Adaptor and 690XL facer to perform facing only. It fits head tubes designed for low profile or, “zero-stack,” headsets. These head tubes have nominal inside diameters of 43.9mm. - 55.9mm (for internal 1.5-inch ZS): The 790 Pilot takes the place of the 789 Reamer when performing head tube facing only. The 790 is used with the HTR-1 Headtube Reamer, the 690-XXL Facing Cutter, and the 750.2 Centering Cone Adaptor. The tool allows facing head tubes with 55.95 – 55.90mm I.D. (“Internal” 1-1/2” ZS standard).
Park Tool Fixed-Gear Lockring Wrench
$17.95
Park's Fixed-Gear Lockring Wrench features 2 different radius hooked spanners for a precise fit, and easy removal and tightening of most fixed-gear lockrings. The HCW-17 fits rings with an outside diameter of 41 to 44mm. It also fits BMX cassette hub lockrings with external notches.
Park Tool Four-Sided Spoke Wrench
$7.95
Park's Four-Sided Spoke Wrenches grip 4 sides of the spoke nipple so they offer an excellent grip and won't slip or round nipples when turning even the tightest spokes and/or aluminum nipples. These popular wrenches also have easy-to-hold vinyl-coated loop handles that are color-coded according to spoke size for easy identification. The loop handle makes them easy to hang on your tool board too.
Park Tool Gear Clean Brush
$4.95
Park's Gear Clean Brush has a handle on one end with a curved, serrated edge perfect for cleaning between cassette cogs. The other end's tough nylon bristles are ideal for cleaning the derailleurs, chain and other drivetrain parts to keep them clean and prevent premature wear. It also works great on brakes and other components that collect dirt and grime. The GearClean easily fits in a toolbox or pack.
Park Tool Handlebar Holder
$19.95
The Handlebar Holder prevents the handlebars and front wheel from swinging to the side and banging into the frame when your bike is mounted in a repair stand. It fits handlebars up to 32mm and all frame tubes up to 50mm in diameter, so it works on almost any road or mountain bike and is sure to make every repair easier.
Park Tool Head Cup Remover (1 to 1-1/4-inch)
$34.95
The RT-1 Head Cup Remover makes headset cup removal easy. The tool is pulled through the frame until the flared ends snap in behind the cup. A blow on the tool head removes the cup. • Fits 1”, 1-1/8” and 1-1/4” headsets • Strong, heat treated alloy steel with nickel finish The RT-1 will also remove the PressFit 30 (PF30) bottom bracket units. The PressFit 30 inside diameter is the same as headset cups, and are pressed in the same manner. SHIS terminology: Removes cups of EC29, EC30, EC34, EC44, ZS41, and ZS44
Park Tool Head Cup Remover - Oversize
$34.95
The RT-2 Head Cup Remover makes headset cup removal easy. The tool is pulled through the frame until the flared ends snap in behind the cup. A blow on the tool head removes the cup. • Designed for the 1-1/4 inch and 1-1/2 inch headest standards • Also easily removes cups on one-piece cranks • Strong, heat-treated alloy steel with a nickel finish SHIS Terminology: The RT-2 will remove cups of ZS44, ZS49, ZS55, ZS56, EC49 and EC56 headsets.
Park Tool Heavy Duty Shop Apron
$29.95
Once you try on Park's Heavy Duty Shop Apron, there's no going back to standard aprons. The SA-3 is made from heavy 10-ounce cotton canvas and has two rows of bar tack reinforced pockets for stashing pens, parts, tools, etc. The special crossback design removes pressure from the neck for all day comfort and a nylon quick release makes the apron easy to adjust and take off. This sweet apron is a full 35-inches in length and the bottom 7-inches of the apron can be snapped up for a custom height fit. Plus, an embroidered Park Tool logo makes the apron as good looking (even when it's dirty) as it is functional.
Park Tool Heavy-Duty Tire Levers
$25.95
Park's Heavy-Duty Tire Levers handle the toughest tire-and-rim combinations including difficult downhill and freestyle tires. Their specially designed tips engage the tire bead so it can be removed with just two levers. Plus, these beefy, forged-steel levers are a full 8-inches long for superior leverage.
Park Tool Hex Wrench (8mm)
$5.95
Park's Hex Wrenches are every mechanic's best friend. They are constructed from industrial quality steel for durability and feature chamfered tips for a precision fit. And, their convenient L shape is perfect for jobs that require lots of leverage or for getting to hard-to-reach bolts.
Park Tool Hex Wrench Set, Ball-End (4, 5, 6mm)
$13.95
Park's AWS-8 Hex Wrench Set features Bondhus balldriver ends, which facilitate use when the tool is at an angle to the bolt. This is great for working in hard-to-reach areas, such as reaching water-bottle-cage screws. The AWS-8 has 4, 5, and 6mm wrenches, which are the most common bicycle bolt sizes. Plus, its Y shape and vinyl coating provide excellent leverage and comfort.